Draw-tite 75730 MAX-FRAME RECEIVER User Manual download pdf

Installation Instructions

Toyota Hilux

Part Numbers:

75730

Hitch Shown In Proper Position

Equipment Required: Pull wire (provided)

Wrenches: 7/8” & 18mm

Existing weldnuts

Bumper

1. Remove the bolts that hold the bumper in place, being careful not to drop the bumper.

2. Lower the bumper and remove the bumper support bolts and bracket from the frame rail. Return brackets to owner to reinstall if

hitch is removed. Fasteners to be re-installed .

3. Raise hitch into place and re-install bolts (removed in step 2) into the weldnuts located on the frame, where the bumper support

brackets were removed.

4. Using the pullwire insert the spacers and carriage bolts into the frame and into the holes in the bottom of the frame as shown.

5. Remove pull wires and install conical washer and hex nuts as shown.

6. Re-install the bumper at the rearward slots on the bracket using the remaining bolts removed in step 1.

7. Torque all fasteners to specification.

Sheet 1 of 3 75730N 9-9-11 Rev. A



Qty. (4) Carriage Bolts 1/2-13 X 2.00 Gr5



Qty. (4) Conical washer ½”



Qty. (4) Spacers ¼ X 1.50 X 2.00



Qty. (4) Hex Nut 1/2-13

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: 75730F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Wiring Access Location: PU3 & PU4

Form: F205 Rev A 5-6-05

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

9,000 (4086 Kg) 900 (409 Kg)

Weight Carrying

Ball Mount

6,000 (2724 Kg) 900 (409 Kg)

Note: Fasteners typical

both sides

Frame

Existing bolts

Both sides







Existing hole

Kink pull wire to keep block

independent of bolt

Example of pull wire procedure

Frame

Bumper



Tighten all 1/2” fasteners with torque wrench to 75 Lb.-Ft. (102 n*m)

Tighten all existing M12 fasteners with torque wrench to 75 Lb.-Ft. (102 n*m)

1 2 3

Summary of Contents

Page 1 - Installation Instructions

Installation Instructions Toyota Hilux Part Numbers: 75730 Hitch Shown In Proper Position Equipment Required: Pull wire (provided) Wrenches: 7/8” &am

Page 2 - Instructions d’installation

Instructions d’installation Toyota Hilux Numéro de pièce : 75730 Attelage montré dans la position appropriée Équipement requis : Fil de tirage (fourni

Page 3 - Instrucciones de instalación

Instrucciones de instalación Toyota Hilux Números de partes: 75730 El enganche se muestra en la posición correcta Equipo necesario: Cable de halar (in

Comments to this Manuals

No comments

Draw-tite 75730 MAX-FRAME RECEIVER User Manual

Browse online or download User Manual for For the car Draw-tite 75730 MAX-FRAME RECEIVER. Draw-Tite 75730 MAX-FRAME RECEIVER User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 75730 MAX-FRAME RECEIVER