Draw-tite 36317 FRAME HITCH User Manual download pdf

Installation Instructions

Chevrolet Malibu – Sedan Only*

Part Numbers:

06988

36317

90132

Hitch Shown In Proper Position

Wiring Access Location: PC3, PC4

Equipment Required: Chisel, Hammer, Cut-off Wheel, Pull Wire (provided)

Wrenches: 13mm, 11/16, 3/4

Drill Bits: 3/8”

1. Lower muffler by removing the two (2) rearmost exhaust hangers.

2. Remove the bottom four (4) 8mm bumper bolts from the end panel.

Note: Do not loosen or remove the top bumper bolt.

3. Remove existing weldnut from end panel on the inboard side of frame rail (see figure 2).

4. If necessary, enlarge existing holes in end panel using a 3/8” drill.

5. Raise hitch into position, aligning slots in hitch with holes in vehicle end panel.

Note: The upright bracket goes on the forward side of the end panel.

Note: SS Model requires fascia trim obtain vehicle owner’s approval. See Figure 5.

6. Loosely install the 3/8” carriage bolts and blocks, conical washers and hex nuts as shown in figure 1.

7. Fishwire 1/2” carriage bolt and block thru large slot in bottom of frame rail as shown. Orient blocks as shown (See Figure 4). Attach conical

washers and nuts as shown.

Note: Keep bolt and block separate while inserting fasteners thru slot (see figure 3).

8. Tighten fasteners to specified torque ratings as follows:

Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 lb.-ft. (41 N*M)

Tighten all ½-13 GR5 fasteners with torque wrench to 75 lb.-ft. (102 N*M)

9. Reinstall exhaust hangers removed in step 1.

Rev. B7-25-06N36317Sheet 1 of 3

z 2003, 2006 Cequent Towing Products

Hex Nut ½-13Qty. (2)

Hex Nut 3/8-16Qty. (4)

Conical Washer ½”Qty. (2)

Conical Washer 3/8”Qty. (4)

Block ¼ x 1-1/2 x 3Qty. (2)

Block 3/16 x 1-1/8 x 2Qty. (4)

Carriage Bolt ½-13 x 2.00Qty. (2)

Carriage Bolt 3/8-16 x 1.50Qty. (4)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent

entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a

vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and

SAE J684.

3500 LB (1 589 Kg) Max Gross Trailer Weight

300 LB ( 136 Kg) Max Tongue Weight

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

Rise

position only.

Drawbar Kit:

36071

Fastener Kit: F36317

Form F206 Rev A 5605

Fascia

* -SS Model requires fascia trim

Obtain vehicle owner’s approval

Bumper

End Panel

Remove M8 bolts. Enlarge existing

Holes with 3/8” drill if necessary

Block

Figure 1

Figure 4

Frame Rail

Vehicle frame

end panel

Remove existing weldnut

Enlarge existing holes with

3/8” Drill if necessary

Top bumper bolt

(do not remove)

Remove existing plastic

Handle bolt and nut.

Figure 2

(Looking rearward on vehicle)

(Passenger side)

Fishwire

Kink pull wire to keep block

independent of bolt

Figure 3

1-1/4”

1-3/4”

Trim Here

Figure 5

SS Model only

Fascia

SS Model Only

1 2 3

Summary of Contents

Page 1 - Installation Instructions

Installation InstructionsChevrolet Malibu – Sedan Only*Part Numbers:069883631790132Hitch Shown In Proper PositionWiring Access Location: PC3, PC4Equip

Page 2 - Instructions d’installation

Instructions d’installationChevrolet Malibu – Sedan Only*Numéros de pièce :069883631790132Attelage montré dans la position appropriéePoints d’accès au

Page 3 - Instrucciones de instalación

Instrucciones de instalaciónChevrolet Malibu – Sedan únicamente*Números de partes:069883631790132El enganche se muestra en la posición correctaUbicaci

Comments to this Manuals

No comments

Draw-tite 36317 FRAME HITCH User Manual

Browse online or download User Manual for For the car Draw-tite 36317 FRAME HITCH. Draw-Tite 36317 FRAME HITCH User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 36317 FRAME HITCH