Draw-tite 75650 MAX-FRAME RECEIVER User Manual download pdf

Installation Instructions

Subaru Forester

Part Numbers:

87493

75650

44607

Hitch Shown In Proper Position

Wiring Access Location: SUV8

Equipment Required: Metal File

Wrenches: ¾”, 10mm

Drill Bits: ½”, 3/8”

1. Lower exhaust by disconnecting (5) rubber exhaust hangers from hanger brackets.

2. Remove forwardmost heat shield screw from each frame rail and discard.

Note: When hitch is installed, heat shield will be sandwiched between frame rail and hitch

3. Remove (2) plastic plugs from existing holes in each frame rail as shown above in Figure 1 and discard.

4. Use 3/8” drill and file to modify forwardmost hole in each frame rail, as shown in Figure 2, to allow fishwiring of spacers and carriage bolts.

5. Fishwire spacer and 7/16” carriage bolt thru access hole modified in Step 4 and down thru center hole in each frame rail (see figure 3). Insert

remaining blocks and ½” carriage bolts into access holes and drop back down thru holes, making sure blocks span both sides of hole (see

Figure 4).

6. Raise hitch into position, being careful not to push fasteners into frame, and secure with conical washers and nuts.

Tighten ½-13 GR5 fasteners to 75 lb.-ft. (102 N*M)

Tighten 7/16-14 GR5 fasteners to 50 lb.-ft. (68 N*M)

7. Raise exhaust back into position and reattach exhaust hangers disconnected in step 1.

z 2012, Cequent Performance Products INC.

Sheet 1 of 3 75650N 7-10-12 Rev. C

Qty. (2) Carriage Bolt – ½-13 x 1.75 GR5

Qty. (2) Hex Nut – ½-13

Qty. (2)

Spacer–¼ x 1 x 3 (Square hole for ½” Carriage

Bolt)

Qty. (2) Conical Washer – 7/16”

Qty. (2) Carriage Bolt – 7/16-14 X 1.75 GR5

Qty. (2) Hex Nut – 7/16-14

Qty. (2)

Spacer–¼ x 1 x 3 (Square hole for 7/16” Carriage

Bolt)

Qty. (2) Pull wire – ½”

Qty. (2) Conical Washer – ½”

Qty. (2) Pull wire – 7/16”

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent

entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a

vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and

SAE J684.

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Fastener Kit: 75650F

Form F206 Rev A 5605

Remove plastic plugs

From existing holes

Both sides

3/8” dia. Drilled holes

Figure 2

Access hole modification to allow

fishwiring of block and carriage bolt

Modify this hole - both

sides to allow fishwiring-

See figure 2

Figure 3

Kink pull wire to keep

Spacer independent of bolt

Existing 7/8”

Diameter hole

in frame

Fascia

A. Insert bolt and

Block into frame

B. Align block on

access hole

C. Pull bolt thru

block

Figure 4

Fishwiring Procedure

Figure 1

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing Not For Use With Spring Bars

Weight Carrying

Ball Mount

4000 (1815 Kg) 600 (272 Kg)

1 2 3

Summary of Contents

Page 1 - Installation Instructions

Installation InstructionsSubaru ForesterPart Numbers:874937565044607Hitch Shown In Proper PositionWiring Access Location: SUV8Equipment Required: Meta

Page 2 - Instructions d’installation

Instructions d’installationSubaru ForesterNuméros de pièces :874937565044607Attelage montré dans la position appropriéePoints d’accès au câblage : SUV

Page 3 - Instrucciones de instalación

Instrucciones de instalación Subaru ForesterNúmeros de partes:874937565044607El enganche se muestra en la posición correcta Ubicación del acceso al ca

Comments to this Manuals

No comments

Draw-tite 75650 MAX-FRAME RECEIVER User Manual

Browse online or download User Manual for For the car Draw-tite 75650 MAX-FRAME RECEIVER. Draw-Tite 75650 MAX-FRAME RECEIVER User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 75650 MAX-FRAME RECEIVER