Draw-tite 36379 FRAME HITCH User Manual download pdf

Installation Instructions

Chevrolet Malibu Maxx

Part Numbers:

36379

06388

90136

Hitch Shown In Proper Position

Wiring Access Location: PC3, PC4

Equipment Required:

Wrenches: ¾, Torque Wrench

Drill Bits: ½”

3500 LB Max Gross Trailer Weight

300 LB Max Tongue Weight

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

RISE

position only.

Drawbar Kit:

36071

Fastener Kit: 36379F

Figure 1.

Frame Rail

Fascia

Access Hole

Qty. (2) Carriage Bolt ½-13 X 2.00 Gr5

Qty. (2) Handle Nut Assembly, ½”

Qty. (2) Block ¼” x 1-1/2” x 3.00 Lg. Qty. (1) Pull Wire

Qty. (4) Conical Toothed Washer ½

Qty. (2) Hex Nut, ½-13

Qty. (2) Hex Bolt, ½-13 x 1.25” LG.

Figure 2.

End Panel

Drilled Hole

1. Raise Hitch into position, aligning the top holes in the Upright Brackets with the existing holes in vehicle end panel.

Note: The Upright Bracket goes on the Forward side of the end panel.

2. Loosely install the ½” x 1-1/4” lg. hex bolts and conical toothed washers thru hole in Hitch and end panel into the handle nut assemblies.

3. Using the Hitch as a template, drill the forward attachment holes for the side arm bars into the bottom of the frame rails.

Note: The driver’s side has an existing hole in bottom of frame to align with slot in the side arm.

4. Fishwire carriage bolt and block through the forward access hole in the bottom of frame rail and through ½” drilled hole and slot in hitch

side arm. NOTE: The fuel filler tube may have to be lowered temporarily to gain proper clearance to access hole on the passenger’s side

frame rail.

5. Loosely install conical toothed washers and hex nuts onto carriage bolts.

z 2005 Cequent Towing Products

Sheet 1 of 3 36379N 10-4-05 Rev. A

Tighten ½-13 GR5 Handle Nut fasteners with torque wrench to 50 Lb.-Ft.

Tighten ½-13 GR5 Carriage Bolt fasteners with torque wrench to 75 Lb.-Ft.

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

1 2 3

Summary of Contents

Page 1 - Installation Instructions

Installation InstructionsChevrolet Malibu MaxxPart Numbers:363790638890136Hitch Shown In Proper PositionWiring Access Location: PC3, PC4Equipment Requ

Page 2 - Instructions d’installation

Instructions d’installationChevrolet Malibu MaxxNuméros de pièces :363790638890136Attelage montré dans la position appropriéePoints d’accès au câblage

Page 3 - Instrucciones de instalación

Instrucciones de instalaciónChevrolet Malibu MaxxNúmeros de partes:363790638890136El enganche se muestra en la posición correctaUbicación del acceso a

Comments to this Manuals

No comments

Draw-tite 36379 FRAME HITCH User Manual

Browse online or download User Manual for For the car Draw-tite 36379 FRAME HITCH. Draw-Tite 36379 FRAME HITCH User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 36379 FRAME HITCH