Draw-tite 75663 MAX-FRAME RECEIVER User Manual download pdf

Installation Instructions

Toyota Venza

Part Numbers:

75663

87521

44604

78235

(U-Haul)

Hitch Shown In Proper Position

Equipment Required:

Wrenches: 17mm

z 2008, 2009 Cequent Performance Products

Sheet 1 of 3 75663N 10-26-09 Rev. C

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: 75663F

Do Not Exceed Lower of Towing Vehicle Manufacturer’s Rating or

Wiring Access Location: SUV3, SUV4

Form: F205 Rev A 5-6-05

Tighten all M10-1.25 X 40mm fasteners with torque wrench to 42Lb.-Ft. (57 N*M)

Qty. (6) M10-1.25 x 40mm CL 10.9 Hex Bolt Qty. (2) 5/16” x 1” x 1-1/2” Block-Spacer, ( AWD vehicles only)

Qty. (6) 3/8” Conical toothed Washer

1. If vehicle is AWD-(All-Wheel Drive), then see Note & Figure B. above. It is important to the proper operation of the vehicle to

reinstall sway bar brackets properly as shown.

2. If vehicle is AWD then remove sway bar brackets both sides, saving existing nuts.

3. Lower exhaust by removing (4) exhaust rubber isolators that support muffler and tailpipe from hangers.

4. Raise hitch into position as shown in Figure A.

above and install (3) 10mm bolts and toothed washers per side into vehicle

frame weldnuts. If vehicle is AWD then reinstall sway bar bracket with spacer block supplied between lower vehicle attachment

and sway bracket as shown in Figure B.

both sides, using existing nut for lower attachment.

5. Tighten bolts to proper torque as described below. Raise exhaust and re-attach rubber isolators.

Vehicle frame

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

4000 (1816 Kg) 400 (182 Kg)

Weight Carrying

Ball Mount

3500 (1589 Kg) 350 (159 Kg)

Figure B.

Note:

AWD MODELS

Existing vehicle sway-bar brackets must be

removed both sides. Then must be reinstalled

with

hitch & spacer blocks, (Item 3), supplied.

Existing sway

bar bracket

Space sway bar

bracket down

with supplied

block.

Figure A.

Existing nut

View underneath vehicle,

Typical both sides.

Vehicle fascia

1 2 3

Summary of Contents

Page 1 - Installation Instructions

Installation InstructionsToyota VenzaPart Numbers:75663 87521 44604 78235 (U-Haul)Hitch Shown In Proper Positio

Page 2 - Instructions d’installation

Instructions d’installationToyota VenzaNuméros de pièces :Attelage montré dans la position appropriéeÉquipement requis :Clés : 17 mm z 2008, 2009 Cequ

Page 3 - Instrucciones de instalación

Instrucciones de instalación Toyota VenzaNúmeros de partes:El enganche se muestra en la posición correcta Equipo necesario:Llaves: 17mm z 2008, 2009