Draw-tite 75645 MAX-FRAME RECEIVER User Manual download pdf

Installation Instructions

Volvo V-70

Volvo XC-70

Note: Fascia trim required

Part Numbers:

75645, 87484, 44597

75178

(U-Haul)

Hitch Shown In Proper Position

Equipment Required: Utility Knife

Wrenches: 8mm, 10mm, 13mm wrench,

17mm wrench, & T-20 Torx Driver ®

Existing

fasteners

Figure 1.

Tighten all M10 CL 8.8 fasteners with torque wrench to 38 Lb.-Ft.(52 N*M)

z 2008, 2009, 2010, 2011, 2012 Cequent Performance Products

Sheet 1 of 6 75645N 3-8-12 Rev. G

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: 75645F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Wiring Access Location: SUV3, SUV4

Form: F205 Rev A 5-6-05

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

Not For Use With Spring Bars

Weight Carrying

Ball Mount

4000 (1814 Kg) 400 (181 Kg)

Notify vehicle owner that the fascia requires trimming to fit hitch.

Recommend: two persons to remove the fascia to prevent scratches or damage.

1. Remove rear bumper fascia. Disconnect back-up sensor wiring if present. (Not shown)

a. Remove (2) plastic fastener from rear of vehicle, between the bottom of the fascia and end panel. See Figure 7.

b. Open tail gate. Remove (2) rubber tailgate stops. See Figure 2.

c. Remove 4 screws (each side) from the plastic wheel well molding. See Figure 4.

d. Gently pull the plastic fascia away from the wheel well molding. See Figure 6.

e. Gently continue to remove fascia. At the tail light pull gently rearward.

f. Pull gently on fascia until the rear fascia is completely removed from vehicle.

2. Loosen the towing eye. See Figure 3.

a. Remove inside appearance panel at rear of tail gate (2) bolts. See Figure 5.

b. Loosen towing eye under appearance panel, rear passenger side (1) bolt. See Figure 5.

3. Remove impact bar. (Continue to loosen towing eye as needed in effort to remove impact bar).

4. Place hitch into impact bar aligning bolt holes

5. Raise hitch and impact bar into position. Re-install existing flange nuts. Hand tightens driver’s side and lower passenger side bolt.

6. Re-install towing eye (sandwich hitch, impact bar and towing eye). Hand tighten (6) bolts. See Figure 1 (Towing eye shown removed for clarity)

7. Tighten fasteners to specification.

8. Re-tighten towing eye from inside vehicle trunk.

9. Replace inside appearance panel at rear of tail gate (2) bolts.

10. Using a utility knife carefully cut out the fascia on the bottom inside fascia. Locate bottom center of the fascia. Trim 2-1/2” wide and 2” long.

See Figure 7. Note: fascia has area to be trimmed for Volvo hitch marked for the Volvo hitch. Obtain vehicle owners approval before cutting.

11. Re-install fascia. Note: making sure fascia sits flat along rear shelf of trunk. Working from the rear forward carefully reinstalls the fascia.

Fascia trim required.

Obtain vehicle owners

approval before

cutting

End panel

Fascia

Impact bar

End panel

Towing eye.

Shown removed.

Figure 2.

Rubber tailgate stops.

Figure 3.

Towing eye.

Shown removed

Note: Installation uses

existing fasteners.

1 2 3 4 5 6

Summary of Contents

Page 1 - Installation Instructions

Installation Instructions Volvo V-70 Volvo XC-70 Note: Fascia trim required Part Numbers: 75645, 87484, 44597 75178 (U-Haul) Hitch Shown In Proper Pos

Page 2

Installation Instructions Volvo V-70 Volvo XC-70 Note: Fascia trim required Part Numbers: Tighten all M10 CL 8.8 fasteners with torque wrench to 38 Lb

Page 3 - Instructions d’installation

Instructions d’installation Volvo V-70 Volvo XC-70 Remarque : Découpage du carénage nécessaire Numéros de pièces : Attelage montré dans la position ap

Page 4

Instructions d’installation Volvo V-70 Volvo XC-70 Remarque : Découpage du carénage nécessaire Numéros de pièces : Figure 4. Serrer toute la visserie

Page 5 - 75645, 87484, 44597

Instrucciones de instalación Volvo V-70 Volvo XC-70 Nota: Se requiere recorte de la placa protectora Números de partes: El enganche se muestra en la

Page 6 - 75645, 87484, 44597

Instrucciones de instalación Volvo V-70 Volvo XC-70 Nota: Se requiere recorte de la placa protectora Números de partes: Apriete todos los tornillos M

Comments to this Manuals

No comments

Draw-tite 75645 MAX-FRAME RECEIVER User Manual

Browse online or download User Manual for For the car Draw-tite 75645 MAX-FRAME RECEIVER. Draw-Tite 75645 MAX-FRAME RECEIVER User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 75645 MAX-FRAME RECEIVER