Draw-tite 36284 FRAME HITCH User Manual download pdf

Installation Instructions

Subaru Legacy Sedan

Subaru Legacy Wagon

Subaru Legacy Outback

Part Numbers:

06287

36284

Hitch Shown In Proper Position

Wiring Access Location: PC1, PC2

Equipment Required:

Wrenches: 12mm, 11/16, ¾, 7/8

Drill Bits: None

1. Lower carbon canister and bracket from passenger side frame rail.

2. Remove the four (4) plastic caps from bottom of frame rails. Fishwire carriage bolts and blocks through access hole in bottom of

frame as shown in Figure 1.

Note:

On driver’s side, side bracket attaches to the outboard side of the tie-down bracket. On passenger’s side, side bracket

attaches to the inboard side of the tie-down bracket.

3. Raise hitch into position. Loosely install hex nuts and conical toothed washers onto forward most fasteners. Install hex bolts and

blocks as shown in Figure 1.

Note:

On passenger’s side, place additional block between hitch and tie-down bracket. See Figure 2.

4. Reinstall large plastic caps into access holes removed in step 2. Reattach carbon canister and bracket.

Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)

Rev. D12-6-07N36284Sheet 1 of 3

z 1999, 2001, 2003, 2004, 2007 Cequent Towing Products

Hex Nut 7/16-14Qty. (2)

Hex Nut ½-13 Qty. (2)

Conical Toothed Washer 7/16Qty. (2)

Lockwasher 1/2Qty. (2)

Spacer ¼ x 1 x 3Qty. (2)

Spacer ¼ x 1 x 2Qty. (5)

Carriage Bolt 7/16-14 x 1-1/2 GR5Qty. (2)

Hex Bolt ½-13 x 2-1/4 GR5Qty. (2)

Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent

entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a

vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and

SAE J684.

3500 LB (1589 Kg) Max Gross Trailer Weight

300 LB (136 Kg) Max Tongue Weight

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

Rise

position only.

Drawbar Kit:

36061

Fastener Kit: K36284

Form F206 Rev A 5605

Frame Rail

Fascia

Optional Drawbar (Sold Separately)

For Legacy Outback Only 36053

Drawbar must be used in the RISE

Position only.

Hitch

Tie-Down Bracket

*Passenger’s side requires

two (2) ¼ x 1 x 2 spacers

Item 2

Figure 2 Figure 1

Access Hole

Frame Rail

Note: Fasteners Typical Both Sides

8765

43221

Side Bracket

90176

1 2 3

Summary of Contents

Page 1 - Installation Instructions

Installation InstructionsSubaru Legacy SedanSubaru Legacy WagonSubaru Legacy OutbackPart Numbers:0628736284Hitch Shown In Proper PositionWiring Access

Page 2 - Instructions d’installation

Instructions d’installationSubaru Legacy SedanSubaru Legacy WagonSubaru Legacy OutbackNuméros de pièces :0628736284Attelage montré dans la position ap

Page 3 - Instrucciones de instalación

Instrucciones de instalaciónSubaru Legacy SedanSubaru Legacy WagonSubaru Legacy OutbackNúmeros de partes:0628736284El enganche se muestra en la posici

Comments to this Manuals

No comments

Draw-tite 36284 FRAME HITCH User Manual

Browse online or download User Manual for For the car Draw-tite 36284 FRAME HITCH. Draw-Tite 36284 FRAME HITCH User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 36284 FRAME HITCH