Draw-tite 24865 SPORTFRAME HITCH User Manual download pdf

Installation Instructions

Ford Fusion

Mercury Milan

Lincoln MKZ

Part Numbers:

Hitch Shown In Proper Position

Wiring Access Location: PC3, 4

Equipment Required: Pullwire (provided) , Lubricant or

Soapy water

Wrenches: 11/16”

1. Lower exhaust pipe by removing the rubber isolator(s) at the muffler(s) and one isolator near the rear suspension. Support the exhaust

to prevent damage. Spraying a lubricant on the metal hanger rod and the rubber isolator helps removal.

2. Using pull wires, feed spacers and carriage bolts into forward hole position (both rails). Access hole located at end of the frame rail

and before the impact bar. Leave pull wire attached. Note: It is much easier if bolt and spacer are not engaged while inserting them

into frame, refer to illustration. See Figure 2.

3. Feed the carriage bolt and spacer thru rearward slots on bottom of frame rails using the pull wires, as shown Figure 3. Note: May

need to insert the carriage bolt in on an angle. Leave the pull wires in position to assist in locating bolt when the hitch is placed in

position.

4. Raise hitch into position as shown in Figure 1. Feeding the pull wires through the holes on the bracket.

5. Remove pull wires and attach conical washers and nuts (be careful not to push fasteners back into frame rail).

6. Torque all fasteners to specifications.

7. Raise exhaust system back into position.

z 2010, 2011 Cequent Performance Products

Sheet 1 of 3 24865N 8-11-11 Rev. C

Qty. (4) Carriage bolt – 7/16-14 X 1-1/4” GR 5

Qty. (4) Washer – conical 7/16”

Qty. (4) Spacer – 1” X 2” X 3/16”

Qty. (4) Nut – 7/16 -14

Tighten all 7/16” fasteners with torque wrench to 50 Lb.-Ft.(68 n*m)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body

panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety

precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.

Regulation V-5 and SAE J684.

2000 LB (908 Kg) Max Gross Trailer Weight

200 LB (90.8 Kg) Max Tongue Weight

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

RISE position only.

Drawbar Kit:

3594

Fastener Kit: 24865F

Form F206 Rev A 5605

Fastener are typical

For both sides

Fascia

Figure 2

Kink Pull wire to keep

spacer independent of bolt

Figure 3.

Forward hole

Rearward slots

Figure 1.

Frame Rail

Access hole

24865

60282

77239

24793 U-Haul

1 2 3

Summary of Contents

Page 1 - Installation Instructions

Installation InstructionsFord Fusion Mercury Milan Lincoln MKZPart Numbers:Hitch Shown

Page 2 - Instructions d’installation

Instructions d’installationNuméros de pièces :Attelage montré dans la position appropriéePoints d’accès au câblage : PC3, 4Équipement requis : Fils de

Page 3 - Instrucciones de instalación

Instrucciones de instalación Números de partes:El enganche se muestra en la posición correcta Ubicación del acceso al cableado: PC3, 4Equipo necesario

Comments to this Manuals

No comments

Draw-tite 24865 SPORTFRAME HITCH User Manual

Browse online or download User Manual for For the car Draw-tite 24865 SPORTFRAME HITCH. Draw-Tite 24865 SPORTFRAME HITCH User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 24865 SPORTFRAME HITCH