Draw-tite 24835 SPORTFRAME HITCH User Manual download pdf

Installation Instructions

Mitsubishi Galant

Part Numbers:

77209

24835

60237

Hitch Shown In Proper Position

Wiring Access Location: TBD

Equipment Required: Torque wrench

Wrenches: 9/16 socket, ¾ socket, 6” extension

Drill Bits: None

1. Lower exhaust by removing bolt in rubber hanger. Bend heat shield slightly to allow clearance for hitch side bracket.

2. Using the pull wire provided, install carriage bolt and spacer into frame rail (driver’s side) through the access hole and into

the rearmost hole in the bottom of the frame rail. See figure 3.

3. Install U-bolts into the rear angled section of the frame as shown. See figure 2.

4. Raise hitch into position, being careful not to push the fasteners into the frame.

5. Install the conical toothed washer, ½ hex nut onto carriage bolt.

6. Install 3/8 flat washers, lock washers, and hex nuts onto u-bolts as shown.

7. Tighten all fasteners to specified torque below.

8. Re-install the exhaust lowered in step one.

Rev. B3-3-0924835NSheet 1 of 3

z 2009 Cequent Towing Products

Hex Nut, 3/8-16Qty. (4)

Hex Nut ½-13 Qty. (1)

Lock Washer, 3/8Qty. (4)

Conical Toothed Washer ½”Qty. (1)

Pull wire, 1/2Qty. (1)

Flat Washer, 3/8-16Qty. (4)

Spacer 1/4” x 1 x 3Qty. (1)

U-Bolt, 3/8-16 x 1.06 GR5Qty. (2)

Carriage Bolt ½-13 x 1.75 GR5Qty. (1)

Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)

Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

2000 LB (908 Kg.) Max Gross Trailer Weight

200 LB (90.8 Kg.) Max Tongue Weight

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

RISE

position only.

Drawbar Kit:

3593

Fastener Kit: 24835F

Form F206 Rev A 5605

Fascia

Vehicle Frame

Figure 1.

Figure 3.

Access Hole

Angle Plate In Frame

Heat Shield

Bend Heat Shield to clear bracket

Figure 2.

U-BOLT INSTALLATION

Insert one end of U-bolt into frame and

rotate into position through frame

1 2 3

Mitsubishi Galant 1

Summary of Contents

Page 1 - Mitsubishi Galant

Installation InstructionsMitsubishi GalantPart Numbers:772092483560237Hitch Shown In Proper PositionWiring Access Location: TBDEquipment Required: Tor

Page 2

Instructions d’installationMitsubishi GalantNuméros de pièces :772092483560237Attelage montré dans la position appropriéePoints d’accès au câblage : T

Page 3

Instrucciones de instalaciónMitsubishi GalantNúmeros de partes:772092483560237El enganche se muestra en la posición correcta Ubicación del acceso al c

Comments to this Manuals

No comments

Draw-tite 24835 SPORTFRAME HITCH User Manual

Browse online or download User Manual for For the car Draw-tite 24835 SPORTFRAME HITCH. Draw-Tite 24835 SPORTFRAME HITCH User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 24835 SPORTFRAME HITCH