Draw-tite 24750 SPORTFRAME HITCH User Manual download pdf

Installation Instructions

Nissan Sentra

Part Numbers:

77126

24750

60826

Hitch Shown In Proper Position

Equipment Required: Pull Wire (provided)

Wrenches: 3/4, 7/8, 11/16

Drill Bits: None

1. Open trunk, lift rug and remove spare tire.

2. Remove both rubber sealing plugs from the bottom of spare tire well. Install carriage bolts and blocks as shown, longer bolt in rearmost hole.

3. Remove (2) plastic fascia push rivets from bottom of rear bumper fascia and retain for re-installation.

4. Position hitch uprights above fascia and loosely attach blocks, conical washers and nuts at spare tire well attachments as shown. Be sure to

install spacer blocks between hitch side arm and rearward attachment to spare tire well as shown.

5. Install blocks and carriage bolts into slots in bumper and down thru slots in hitch uprights using pull wire provided as shown. Install conical

washers and nuts

Note: Kink pull wire to keep block independent of bolt as shown in Figure 2.

6. Reinstall push rivets back into bumper fascia.

7. Apply sealant at carriage bolt attachments inside spare tire well to prevent the intrusion of water and exhaust fumes to vehicle interior.

8. Replace spare tire and rug.

Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)

Rev. D10/27/0624750NSheet 1 of 3

z 2005, 2006 Cequent Towing Products

Conical Toothed Washer 7/16Qty. (2)

Block ¼ x 1-3/4 x 2-1/2Qty. (2)

Block ¼ x 1 x 3Qty. (2)

Hex Nut 7/16-14Qty. (2)

Block ¼ x 2 x 2Qty. (2)

Hex Nut ½-13Qty. (2)

Carriage Bolt ½-13 x 2-1/4Qty. (2)

Conical Toothed Washer ½”Qty. (2)

Carriage Bolt 7/16-14 X 1-1/2Qty. (2)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

Rise

position only.

Drawbar Kit:

3593

Fastener Kit: 24750F

Form F206 Rev A 5605

Bumper

Spare Tire

Well

Fascia

Bumper

Bumper Fascia

Spare Tire

Well

Hitch Side Arm

Apply sealant

Between blocks

And well

Hitch Uprights

Pull Wire

Remove rubber

Sealing plugs

1598

Existing hole

Kink pull wire to keep block

independent of bolt

Example of pull wire procedure

Bumper

Figure 2

Figure 1

Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)

2000 LB (908 Kg) Max Gross Trailer Weight

200 LB (90.8 Kg) Max Tongue Weight

Wiring Access Location: PC3, PC4

1 2 3

Summary of Contents

Page 1 - Installation Instructions

Installation InstructionsNissan SentraPart Numbers:771262475060826Hitch Shown In Proper PositionEquipment Required: Pull Wire (provided)Wrenches: 3/4,

Page 2 - Instructions d’installation

Instructions d’installationNissan SentraNuméros de pièce :771262475060826Attelage montré dans la position appropriéeÉquipement requis : Fil de tirage

Page 3 - Instrucciones de instalación

Instrucciones de instalaciónNissan SentraNúmeros de partes:771262475060826El enganche se muestre en la posición correctaEquipo necesario: Pull Wire (s

Comments to this Manuals

No comments

Draw-tite 24750 SPORTFRAME HITCH User Manual

Browse online or download User Manual for For the car Draw-tite 24750 SPORTFRAME HITCH. Draw-Tite 24750 SPORTFRAME HITCH User Manual [es]

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 24750 SPORTFRAME HITCH