Draw-tite 24907 SPORTFRAME HITCH User Manual download pdf

Installation Instructions

Nissan Sentra

(WILL NOT FIT SR MODEL)

Part Numbers:

60338

24907

77294

Hitch Shown In Proper Position

Equipment Required: Power Drill

Wrenches: 9/16 , 11/16

Drill Bits: 1” , 7/16

1. Hold hitch in place and use as a template to mark holes needed to be drilled in the driver side frame rail. (Hitch can be held up by

the tow hook mount and the 3/8” bolts if needed). Remove hitch after holes are marked in there correct locations.

2. Fish wire bolts and square hole washers up thru the middle access hole in the frame and out the 2 attachment holes.

3. Raise hitch into position over the bolts in the frame and attach the 7/16” conical and nut. 3/8” bolts will push through the passenger

side end panel holes that line up with the hitch at the frame rail. Install the 3/8” conical and nuts using a 9/16” socket and a box end

wrench on the end panel side.

4. Install the 7/16” Carriage Bolt and Block thru the vehicle tow hook and the bracket on hitch. Secure bolt using the 11/16” socket or

box end wrench.

Tighten all 3/8” fasteners with torque wrench to 35 Lb.-Ft.

Qty. (3) CARRIAGE BOLT – 7/16-14 X 1.75 GR5

Qty. (1) BLOCK .250 x 1.00 x 3.00

Qty. (3) CONICAL WASHER – 7/16”

Qty. (2) LOCKNUT FLG 3/8-16

Qty. (3) HEX NUT – 7/16-14

Qty. (2) CONICAL WASHER 3/8

Qty. (2) 7/16" SQ HOLE WASHER

Qty. (2) PULL WIRE – 7/16”

Qty. (2) BOLT 3/8-16 X 1.25

Tighten all 7/16” fasteners with torque wrench to 50 Lb.-Ft.

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent

entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a

vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and

SAE J684.

Fastener Kit: 24907F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Wiring Access Location: PC3,4

Form: F205 Rev C 9-17-2012

Accessory Rating

Figure 4

Fishwiring Location

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Carrying

Ball Mount

2000 (907 Kg) 200 (91 Kg)

Fascia

Frame

End Panel

Tow hook

Drawbar must be used in the

RISE position only.

Drawbar Kit:

3593

DRILL ACCESS HOLE

IN BOTTOM OF FRAME

FRAME

EXISTING HOLE

EXAMPLE OF FISHWIRE PROCEDURE

KINK FISHWIRE

TO KEEP BLOCK

INDEPENDENT OF BOLT

DRILLED HOLE

1 2 3

Summary of Contents

Page 1 - Installation Instructions

Installation Instructions Nissan Sentra (WILL NOT FIT SR MODEL) Part Numbers: 60338 24907 77294 Hitch Shown In Proper Position Equipment Required: Pow

Page 2

Installation Instructions Nissan Sentra (WILL NOT FIT SR MODEL) Part Numbers: 60338 24907 77294 Hitch Shown In Proper Position Équipement requis : Per

Page 3 - Instrucciones de instalación

Instrucciones de instalación Nissan Sentra (NO SE AJUSTA AL MODELO SR) Números de partes: 60338 24907 77294 El enganche se muestra en la posición corr

Comments to this Manuals

No comments

Draw-tite 24907 SPORTFRAME HITCH User Manual

Browse online or download User Manual for For the car Draw-tite 24907 SPORTFRAME HITCH. Draw-Tite 24907 SPORTFRAME HITCH User Manual [es]

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 24907 SPORTFRAME HITCH