Draw-tite 36282 FRAME HITCH User Manual download pdf

Installation Instructions

Lincoln LS

*For 2003 Models Additional

Installation Time Required

Part Numbers:

90143

36282

06393

Hitch Shown In Proper Position

Wiring Access Location: PC3, PC4

Equipment Required: Utility Knife, Fishwire (provided)

Wrenches: 11/16

Drill Bits: 7/16

For 2003 Models Fascia Trimming Is Required

1. Disconnect the two (2) fascia tabs holding the lower fascia to the trunk pan.

2. Fishwire the forward fasteners in the frame rail as Shown above.

3. Apply the Galvanic isolator shields to the blocks and hitch tabs that contact the aluminum bumper.

4. Raise the hitch into position and attach with forward fasteners. On 2003 vehicles, notch fascia as necessary. Obtain vehicle

owners approval before cutting

5. Using the hitch as a template, drill two (2) 7/16” holes in the bumper.

6. Fishwire carriage bolts and blocks thru holes in bumper and install lock washers and nuts.

7. Reattach the lower fascia tabs with cable ties provided.

Rev. C3-8-06N36282Sheet 1 of 3

z1999, 2001, 2003, 2006 Cequent Towing Products

Galvanic Isolator Shield (not shown)Qty. (8)

BlockQty. (4)

Cable Tie (not shown) Qty. (2)

Lock Washer 7/16Qty. (4)

Hex nut 7/16-14Qty. (4)

Carriage Bolt 7/16-14 X 1.50Qty. (4)

Tighten all 7/16-14 GR fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

3500 LB (1589 Kg) Max Gross Trailer Weight

300 LB (136 Kg) Max Tongue Weight

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

RISE

position only.

Drawbar Kit:

36071

Fastener Kit: K36282

Frame rail

Bumper

Fascia

Fascia trim required. Obtain vehicle

owners approval before cutting

Fascia trim required. Obtain vehicle

owners approval before cutting

Frame rail

Access hole

Bottom of Fascia

Drilled hole

Fascia

Disconnect lower fascia tabs and

reattach using cable ties provided

IMPORTANT

Install two (2) galvanic

isolator shields per

bumper mounting block.

Isolator shield must be

placed between block

and aluminum bumper

IMPORTANT

Install two (2) galvanic

isolator shields per

bumper mounting tab.

Isolator shields must be

placed between hitch

and aluminum bumper

Fasteners typical both sides.

2003 Vehicles

Both sides

Form F206 Rev A 5605

1 2 3

Summary of Contents

Page 1 - Installation Instructions

Installation InstructionsLincoln LS*For 2003 Models AdditionalInstallation Time RequiredPart Numbers:901433628206393Hitch Shown In Proper PositionWiri

Page 2 - Instructions d’installation

Instructions d’installationLincoln LS*Modèles 2003 : Le temps d’installation est plus long.Numéros de pièces :901433628206393Attelage montré dans la p

Page 3 - Instrucciones de instalación

Instrucciones de instalación Lincoln LS*Para los modelos 2003 se requieretiempo de instalación adicionalNúmeros de Partes:901433628206393El enganche s

Comments to this Manuals

No comments

Draw-tite 36282 FRAME HITCH User Manual

Browse online or download User Manual for For the car Draw-tite 36282 FRAME HITCH. Draw-Tite 36282 FRAME HITCH User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 36282 FRAME HITCH