Draw-tite 41990 SERVICE BODY RECEIVER User Manual download pdf

Installation Instructions

Part Number:

41990

z 2008 Cequent Towing Products - Printed in Mexico

Sheet 1 of 6 41990N 5-7-08 Rev. B

Note: check hitch frequently for damage, making sure hitch ball is properly tightened. A hitch or ball which has been damaged should be removed and replaced.

Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies

with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.

Do Not Exceed Lower of Towing Vehicle Manufacturer’s Rating

or Max Gross Trailer WT / Max Tongue WT ratings below

Hitch type

Max Gross

Trailer WT

Max Tongue

Weight Carrying

Ball Mount

16,000lb. (7264 Kg) 1600lb. (726 Kg)

Form: F205 Rev A 5-6-05

Installation Instructions

Service Body Hitch – Long Tube

Requires Bracket kit 4907 or 4916

not included with this product to complete installation.

WARNING! THIS PRODUCT IS NOT TO BE USED WITH A

WEIGHT-DISTRIBUTING HITCH SYSTEM.

Use in weight-carrying mode only.

The above weight ratings only apply to this product properly

installed in strict accordance to these instructions by trained

personnel. It is the responsibility of the installer to assure that all of

these and following or subsequent instructions, requirements and

warnings are properly met.

WARNING!

Failure to follow all

warnings and instructions

may result in product

failure, property damage,

serious bodily injury,

and/or death.

NOTE!

Read, understand,

follow and save these

instructions. Install

and use this product

only as specified in

these instructions.

Never allow

installation or use of

this product by

anyone without

providing them with

these instructions.

Installer must follow

and understand all

instructions and

warnings for any

product(s) to which

this product is used in

conjunction with or

installed.

NOTE!

Note! The installation of this hitch product must be performed only by experienced and trained mechanics,

technicians, welders etc. This product is not intended to be installed by an average consumer not familiar with or

experienced in installing towing components on commercial vehicles. Attaching this hitch product to tow vehicle

frame may void vehicle manufacturer(s) warranty. Check with vehicle manufacturer(s) before installing this product.

This product is authorized for use with appropriate Bulldog, Draw-Tite, Hidden Hitch, Highland, Reese, Rola, & Tow-Ready brand accessories.

Diagram 1.

Tow vehicle frame

Make sure that paint has been removed from all surfaces

requiring welding. Weld frame brackets to hitch center section

all the way around complete. Either on inside or outside of

frame brackets. 1/4” fillet welds required. 5/16” minimum tube

must be exposed to weld on outside of frame brackets.

Make sure that hitch

receiver opening is

centered with tow vehicle

before welding.

6” long 1/4” fillet

welds required top

and bottom of tow

vehicle frame to hitch

frame bracket, typical

both sides. Wrap end

of welds 1/2” typical.

See Diagram 3

following page for

more detail.

Note!

It may be easier to

weld frame brackets to

hitch center section

before installing hitch

to tow vehicle.

Note! You must use

frame brackets,

part number

4907 or 4916,

(sold separately), to

complete this installation.

Part number

41990

4907 frame

bracket kit

shown.

4916 kit similar.

Bolt-on option details

shown in Diagram 2.

on next page.

1 2 3 4 5 6

Summary of Contents

Page 1 - Installation Instructions

Installation Instructions Part Number: 41990 z 2008 Cequent Towing Products - Printed in Mexico Sheet 1 of 6 41990N 5-7-08 Rev. B Note: check hitc

Page 2

Installation Instructions Part Number: 41990 Installation Instructions Service Body Hitch – Long Tube Requires Bracket kit 4907 or 491

Page 3 - Número de parte:

Instrucciones de instalación Número de parte: 41990 z 2008 Cequent Towing Products - Impreso en México Hoja 3 de 6 41990N 5-7-08 Rev. B Nota: Rev

Page 4

Instrucciones de instalación Número de parte: 41990 Instrucciones de instalación Enganche de carrocería de servicio – Tubo Largo Req

Page 5 - Instructions d’installation

Numéro de pièce : 41990 z 2008 Cequent Towing Products - Imprimé au Mexique Feuille 5 de 6 41990N 5-7-08 Rev. B Remarque : Vérifier l’attelage fré

Page 6

Numéro de pièce : 41990 Instructions d’installation Attelage de carrosserie-atelier – Tubulure Long Requiert le nécessaire de supports 4907 ou 4916, n

Comments to this Manuals

No comments

Draw-tite 41990 SERVICE BODY RECEIVER User Manual

Browse online or download User Manual for For the car Draw-tite 41990 SERVICE BODY RECEIVER. Draw-Tite 41990 SERVICE BODY RECEIVER User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 41990 SERVICE BODY RECEIVER