Draw-tite 24894 SPORTFRAME HITCH User Manual download pdf

Installation Instructions

Chevy Spark 2LT

Part Numbers:

24894

60313

77282

Hitch Shown In Proper Position

Wiring Access Location: PC3, PC4

Equipment Required: 7/16” Pull Wire

Wrenches: 11/16”, 7/8”

Drill Bits: 1/2”

1. Lower the exhaust by removing the rubber exhaust isolator located above the muffler.

2. Use 1/2” drill to enlarge the existing 3/4” holes on both frame rails as shown in Figure 1.

3. Install 7/16” carriage bolts and 7/8” blocks using the reverse pull wire procedure shown in Figure 2. Leave pull wires attached.

4. Raise hitch into position and feed pull wires through the holes on the hitch brackets.

5. Install the 1/2” carriage bolt and 2” x 2” spacer to tie down hook as shown in Figures 3 & 4. Do not tighten down at this point.

6. Feed the 7/16” carriage bolts though the holes on the hitch brackets, remove pull wires, and install fasteners as shown in Figure 3.

7. Center the hitch on the vehicle and torque all fasteners to the specifications shown below.

8. Reinstall exhaust.

z 2012 Cequent Performance Products, Inc.

Sheet 1 of 3 24894N 8-6-12 Rev. A

Qty. (2) 7/16”-14 x 1.50” Carriage Bolt GR.5

Qty. (1) 1/2”-13 x 1.75” Carriage Bolt GR.5

Qty. (2) 3” x 7/8” Block

Qty. (1) 2” x 2” Spacer

Qty. (2) 7/16” Conical Washer

Qty. (1) 1/2” Conical Washer

Qty. (2) 7/16”-14 Hex Nut GR. 2

Qty. (1) 1/2”-13 Hex Nut GR. 2

Tighten all 1/2”-13 fasteners with torque wrench to 75 Lb.-Ft (102 N-M).

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

RISE position only.

Fastener Kit: 24894F

Fascia

2000 LB (908 Kg) Max Gross Trailer Weight

200 LB (90.8 Kg) Max Tongue Weight

Tighten all 7/16” fasteners with torque wrench to 50 Lb.-Ft (68 N-M).

A. Insert bolt and

Block into frame

B. Align block on

access hole

C. Pull bolt thru

block

Figure 2: Pull Wire Procedure

Figure 1: Access hole modification to allow

pull wiring of block and carriage bolt

0.563 (14.30 mm)

Tie down hook

Note: Orientation of Block

Figure 4: Back view of

properly Fastened

To Tie Down Hook

Drawbar Kit:

3594

Note: Drill rearward

of existing 3/4”

diameter hole

in frame rail

Figure 3: Hitch Installation

Tie down hook

Hitch

Pull Wire

1 2 3

Summary of Contents

Page 1 - Installation Instructions

Installation Instructions Chevy Spark 2LT Part Numbers: 24894 60313 77282 Hitch Shown In Proper Position Wiring Access Location: PC3, PC4 Equipment

Page 2 - 60313

k o j n l k j l m m p q Instructions d'installations Chevy Spark 2LT Numéros de pièces : 24894 60313 77281 Attelage montré en position adéquate

Page 3 - Instrucciones de instalación

k o j n l k j l m m p q Instrucciones de instalación Chevy Spark 2LT Números de partes: 24894 60313 77281 El enganche se muestra en la posición corr

Comments to this Manuals

No comments

Draw-tite 24894 SPORTFRAME HITCH User Manual

Browse online or download User Manual for For the car Draw-tite 24894 SPORTFRAME HITCH. Draw-Tite 24894 SPORTFRAME HITCH User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 24894 SPORTFRAME HITCH