Draw-tite 118555 T-ONE CONNECTOR User Manual download pdf

WARNING

If routing the wire thru a grommet and along the

exterior of the vehicle, be careful to avoid any hot

pipes, heat shields, the fuel tank or any other points

that may pinch or break the wire.

9. Disconnect the vehicle’s negative (-) battery cable.

If not removed, remove the fuse from the yellow

fuse holder (provided). After cutting the fuse holder

wire

, attach the ring terminal and secure to the

vehicle’s Positive (+) battery cable

. Connect the

other end of the fuse holder to the black 12 ga. wire,

using the yellow butt connector (provided).

WARNING

Read and follow all warnings and cautions printed on

the tow vehicle’s battery.

WARNING

All connections must be complete for the T-Connector

to function properly. Test and verify installation with a

test light or trailer once installed. For initial test, reset

vehicle electrical system by temporarily removing the

key from the ignition

10. Secure the remainder of the T-Connector harness

with the cable ties provided, to prevent damage or

rattling and being careful to avoid any areas that

would pinch, cut or melt the wire.

11. Replace carpet, and any other clips or panels that

were removed during installation being careful not

to cut or pinch the wires.

NOTE

Store 4-Flat in trunk area when not in use.

WARNING

Overloading circuit can cause fires. DO NOT

exceed lower of vehicle manufacturer rating or:

• Max. stop/turn light: 2 per side (4.2 amps)

• Max. tail lights: (7.5 amps)

Read vehicle’s owners manual & instruction sheet

for additional information.

ENGLISH

TOOLS REQUIRED:

Trim Panel Remover, 10mm Socket & Ratchet

or 10mm Wrench, Drill (3/32” Drill Bit),

1/4” Socket, Wire Crimpers, Wire Cutters,

Philips Head Screwdriver, Test-probe

Sedan Only

Open trunk and remove threshold panel. Partially

remove the corner felt trunk liner, on both sides,

exposing the vehicle’s taillight wiring harness

Hatchback Only

Open hatch to locate the vehicle wiring inside

the vehicle’s rear cargo area by partially removing

the plastic threshold cover, side panels, and cargo

trays

fgh

All Models

Behind the taillights, there will be connection points

matching the ends of the T-Connector adapter on the

back of each of the vehicle taillight housings.

Beginning on the driver’s side, separate the vehicle’s

wiring connectors, being careful not to break the

locking tabs.

Insert the T-Connector end, with the yellow wire,

between the vehicle wiring connectors and lock

into place. Ensure that the connectors are fully

inserted with locking tabs in place.

4. Route the T-Connector end with green wire to the

passenger ‘s side behind the panels and along the

threshold. Repeat step 3 for T-Connector end with

the green wire.

5. Locate a suitable grounding point on the driver’s side

near the connectors. Drill a 3/32” hole and secure

white wire with eyelet using screw provided. Do not

drill into any exposed surfaces.

CAUTION

Verify what is behind any surface prior to drilling

to avoid damage to the vehicle and/or personal injury.

Do not drill into any exposed surfaces.

6. Locate the T-Connector’s Grey 12-Pin connector

and insert it into the mating connector located

on the black box-module. Check to see that the

mating surfaces of the wiring connectors match.

All connector surfaces should be clean and free

of dirt. Be careful not to damage the locking tabs

and be sure that connectors are fully inserted with

locking tabs in place

7. Locate a flat surface in an out of the way place

and mount the T-Connector’s black box-module,

to prevent damage or rattling.

NOTE

This surface should be in an area that is free of

any moisture and mounted in an area that it is high

enough where it could not be exposed to direct

contact with any water or liquid substance.

WARNING

The black box-module is intended to be mounted

ONLY in the INTERIOR of the vehicle. Mounting on

the exterior or areas exposed to the elements or

moisture could cause serious damage to the vehicle

and module. Secure the remainder of the T-Connector

harness with the cable ties provided, to prevent

damage or rattling and being careful to avoid any

areas that would pinch, cut or melt the wire.

8. From inside the vehicle, connect the black 12 ga.

wire and the black wire from the T-Connector black

box with the supplied yellow butt connector. Either

route the black wire thru a grommet and along the

exterior frame or follow the existing wiring along

the thresholds into the engine compartment up to

the battery avoiding areas that may pinch or break

the wire

READ THIS FIRST:

Read and follow all vehicle warnings and

installation instructions before beginning installation.

Wear safety glasses and use all safety precautions

during installation.

LISEz CECI EN PREMIER:

Lire et observer toutes les consignes de sécurité et les

instructions avant de commencer l’installation. Durant

l’installation, veiller à toujours porter des lunettes

de protection et respecter les mesures de sécurité.

LEA ESTO PRIMERO:

Lea y siga todas las advertencias e instrucciones

de instalación del vehículo antes de empezar la

instalación. Use gafas de seguridad y todas las

precauciones de seguridad durante la instalación.

118555-037 Rev. A 11/28/2011

Installation Instructions

Directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

Sonic Sedan Sonic Hatch

1 2

Summary of Contents

Page 1 - All Models

WARNINGIf routing the wire thru a grommet and along the exterior of the vehicle, be careful to avoid any hot pipes, heat shields, the fuel tank o

Page 2 - FraNçaIS

FraNçaISOUTILS REQUIS: Écarteur de panneau de garnisage, Cliquet et douille de 10 mm ou clé de 10 mm, Perceuse (mèche de 3/32 po), Douille 1/4 po, Ser

Comments to this Manuals

No comments

Draw-tite 118555 T-ONE CONNECTOR User Manual

Browse online or download User Manual for For the car Draw-tite 118555 T-ONE CONNECTOR. Draw-Tite 118555 T-ONE CONNECTOR User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 118555 T-ONE CONNECTOR