READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEZ CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.
118269-037 Rev. A 04/15/13
Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, Wire Cutters,
10mm Socket & Ratchet or 10mm Wrench,
Philips Head Screwdriver, Test-probe
1. KIA Sorento:
Lower spare tire to gain access to vehicle wiring.
Hyundai Veracruz:
Find access hole inside the bumper support
channel, above passenger side exhaust,
and route T-Connector harness plugs though
hole
d
.
2. KIA Sorneto:
Underneath the vehicle, on the passenger’s
side, on top of the frame rail near the rear tire,
locate the vehicle Tow-Plug harness. It will have
a connection point matching the T-Connector
harness. Remove protective cap, being careful
not to break the locking tabs. All connector
surfaces should be clean and free of dirt
e
.
NOTE
On some vehicles, the vehicle wiring harness
is located behind a protective cover on the
drivers side frame rail. Remove the plastic
trim fasteners, securing the protective cover,
to access vehicle’s wiring harness.
f
.
Hyundai Veracruz:
Locate the vehicle Tow-Plug harness underneath
the vehicle, on the passenger’s side frame,
near the rear tire. It will have a connection point
matching the T-Connector harness. Remove
protective cap, being careful not to break the
locking tabs. All connector surfaces should be
clean and free of dirt
g
.
3. Remove he vehicle tow plug protective
caps and return to customer. All connector
surfaces should be clean and free of dirt.
Insert the T-Connector harness into the vehicle’s
Tow-Plug harness and lock into place. Be sure
that connectors are fully inserted with locking
tabs in place.
4. KIA Sorneto:
Route the T-Connector harness rearward to
the back of the fascia of the bumper. Route
the T-Connector harness along the inside of
bumper toward the center of vehicle
h
.
Hyundai Veracruz:
Route the T-Connector harness along the inside
of bumper support channel toward the center
of vehicle. Mount the 4-Flat end in an accessible
location with a bracket or electrical box
(not included)
i
.
WARNING
Route the wire being careful to avoid any hot
pipes, heat shields, the fuel tank or any other
points that may pinch or break the wire.
5. Mount the T-Connector black box using
double-sided tape provided onto the bottom
of the bumper support channel. Secure all
loose wires with cable ties
j
.
6. All connections must be complete for the
T-Connector to function properly. For initial test,
reset vehicle electrical system by temporarily
removing the key from the ignition. Test and
verify installation with a test light or trailer
once installed.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer rating or:
• Max. stop/turn light: 2 per side (4.2 amps)
• Max. tail lights: (7.5 amps)
Read vehicle’s owners manual & instruction
sheet for additional information.
d g
h i
j
Hyundai VeracruzKia Sorento
e
f
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals