Draw-tite 75162 MAX-FRAME RECEIVER User Manual download pdf

Installation Instructions

Dodge Durango

Chrysler Aspen

Part Numbers:

75162

33082

87562

Hitch Shown In Proper Position

Equipment Required: Knife or small hand saw

Wrenches: 11/16, 3/4

Drill Bits: 1/2

1. Lower spare tire.

2. Trim styrofoam/plastic fascia support as shown in figure 3 for installation of u-bolts.

Note: Trimming of styrofoam/plastic necessary to insure proper seating of receiver on vehicle crossmember.

3. Install u-bolts over vehicle crossmember at cutouts in styrofoam/plastic.

4. Raise hitch into position, attaching loosley to u-bolts with lockwashers and nuts.

5. Center hitch on vehicle.

Tighten 7/16-20 nuts to 55 lb.-ft. (75 N*M), hitch should fit flat against bottom of vehicle crossmember.

6. Remove (4) fasteners which secure fascia to fascia mounting brackets. Push fascia up to allow access to drill thru (2) holes in

hitch bar into rear face of vehicle crossmember. Drill (2) holes thru hitch plate and into front face of vehicle crossmember.

7. Install ½-13 X 4.00 GR5 hex bolts and hardened flat washers as shown. Install lockwashers and nuts.

Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)

8. Re-install fascia mounting fasteners.

9. Raise spare tire back into position.

Rev. B9-22-06N75162Sheet 1 of 3

z 2004, 2006 Cequent Towing Products

1/2 LockwasherQty. (2)

7/16-20 U-BoltQty. (2)

1/2-13 Hex NutQty. (2)

1/2 Hardened Flat WasherQty. (2)

7/16 LockwasherQty. (4)

1/2-13 X 4.00 GR5 Hex BoltQty. (2)

7/16-20 Hex NutQty. (4)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: F75162

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

600 (272 kg)6000 (2722 kg)

Weight Carrying

Ball Mount

900 (408 kg)9000 (4082 kg)

Weight Distributing

Max Tongue

WT (LB)

Max Gross

Trailer WT (LB)

Hitch type

Wiring Access Location: SUV1, SUV2

Form: F205 Rev A 5-6-05

Fascia

Styrofoam/Plastic

Fascia

Reinforcement

Hitch Plate

Hitch Bar

Vehicle

Crossmember

Figure 1

Figure 2

Figure 3

Styrofoam/Plastic

Fascia

Reinforcement

Fascia support bracket

at centerline of vehicle

Drill 1/2” hole after tightening

7/16” fasteners – (4) places

Approx.

11.25 Inside / Inside Gussets

.750 Wide

cutout

measured

from edge

of gusset-

both sides.

1 2 3

Summary of Contents

Page 1 - Installation Instructions

Installation InstructionsDodge Durango Chrysler AspenPart Numbers:75162 33082 87562Hitch Shown In Proper PositionEquipment Required: Knife or small h

Page 2 - Instructions d’installation

Instructions d’installationDodge Durango Chrysler AspenNuméros de pièces :75162 33082 87562Attelage montré dans la position appropriéeÉquipement requi

Page 3 - Instrucciones de instalación

Instrucciones de instalaciónDodge Durango Chrysler AspenNúmeros de partes:75162 33082 87562El enganche se muestra en la posición correctaEquipo necesa

Comments to this Manuals

No comments

Draw-tite 75162 MAX-FRAME RECEIVER User Manual

Browse online or download User Manual for For the car Draw-tite 75162 MAX-FRAME RECEIVER. Draw-Tite 75162 MAX-FRAME RECEIVER User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 75162 MAX-FRAME RECEIVER