Draw-tite 118569 T-ONE CONNECTOR User Manual download pdf

ENGLISH

TOOLS REQUIRED:

10mm Socket & Ratchet or 10mm Wrench,

Drill (3/32” Drill Bit), 1/4” Socket, Test-probe

1. Open the vehicle’s rear tailgate. Locate the grey

tow plug by opening the access panel inside of

the storage compartment

2. Insert the T-Connector harness into the

vehicle’s Tow-Plug harness and lock into place.

WARNING

All connector surfaces should be clean and

free of dirt. Be careful not to damage the

locking tabs and be sure that connectors

are fully inserted with locking tabs in place.

3. Locate a suitable grounding point. Drill a

3/32” hole and secure the white wire using

the eyelet and screw provided. Do not drill

into any exposed surfaces.

4. Mount the T-Connector black box using

double-sided tape provided.

WARNING

The black box-module is intended to be

mounted ONLY in the INTERIOR of the vehicle.

Mounting on the exterior or areas exposed to

the elements or moisture could cause serious

damage to the vehicle and module.

5. Open vehicle hood, and locate the fuse box

on the driver side near the front of the vehicle.

Unlatch the fuse door to access the fuse area.

Locate position labeled (20A) Trailer. Insert

the 20 amp fuse included with the T-Connector

package in this position and latch the fuse

box

WARNING

All connections must be complete for the

T-Connector to function properly. Test and

verify installation with a test light or trailer

once installed. For initial test, reset vehicle

electrical system by temporarily removing

the key from the ignition.

6. Store 4-Flat connector in rear cargo area

when not in use.

WARNING

Overloading circuit can cause fires. DO NOT

exceed lower of towing manufacturer rating or:

• Max. stop/turn light: 2 per side (4.2 amps)

• Max. tail lights: (7.5 amps)

Read vehicle’s owners manual & instruction

sheet for additional information.

READ THIS FIRST:

Read and follow all vehicle warnings and

installation instructions before beginning installation.

Wear safety glasses and use all safety precautions

during installation.

LISEz CECI EN PREmIER:

Lire et observer toutes les consignes de sécurité et les

instructions avant de commencer l’installation. Durant

l’installation, veiller à toujours porter des lunettes

de protection et respecter les mesures de sécurité.

LEA ESTO PRImERO:

Lea y siga todas las advertencias e instrucciones

de instalación del vehículo antes de empezar la

instalación. Use gafas de seguridad y todas las

precauciones de seguridad durante la instalación.

118569-037 Rev. A 10/9/2012

Installation Instructions

Directives de montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

Acura RDX

1 2

TOOLS REQUIRED: 1
FraNçaIS 2

Summary of Contents

Page 1 - TOOLS REQUIRED:

ENGLISHTOOLS REQUIRED: 10mm Socket & Ratchet or 10mm Wrench, Drill (3/32” Drill Bit), 1/4” Socket, Test-probe1. Open the vehicle’s rear tailgate.

Page 2 - FraNçaIS

ESpaÑoLHERRAmIENTAS NECESSARIAS: Encaje y trinquete de 10mm o llave de tuercas de 10mm, Taladro (broca de 3/32”), Llave de tubo de 1/4”, Terminal de

Comments to this Manuals

No comments

Draw-tite 118569 T-ONE CONNECTOR User Manual

Browse online or download User Manual for For the car Draw-tite 118569 T-ONE CONNECTOR. Draw-Tite 118569 T-ONE CONNECTOR User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 118569 T-ONE CONNECTOR