Draw-tite 118520 T-ONE CONNECTOR User Manual download pdf

READ THIS FIRST:

Read and follow all vehicle warnings and

installation instructions before beginning installation.

Wear safety glasses and use all safety precautions

during installation.

LISEZ CECI EN PREMIER:

Lire et observer toutes les consignes de sécurité et les

instructions avant de commencer l’installation. Durant

l’installation, veiller à toujours porter des lunettes

de protection et respecter les mesures de sécurité.

LEA ESTO PRIMERO:

Lea y siga todas las advertencias e instrucciones

de instalación del vehículo antes de empezar la

instalación. Use gafas de seguridad y todas las

precauciones de seguridad durante la instalación.

118520-037 Rev. A 03/12/08

Installation Instructions

Directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

ENGLISH

TOOLS REQUIRED:

Test-probe, Trim Panel Puller, Drill (3/32” Drill Bit),

10mm Socket, Ratchet, Wire Cutter, Wire Crimper,

Phillips Head Screwdriver

1. Open rear door and fold rear seat forward

. Remove

threshold, trunk ﬂoor panels and trays. Set aside all

items removed being careful not to damage parts

2. On both sides of the vehicle, remove cargo loops and

phillips head screws

, so that the trim panels can

be carefully pulled away from the vehicle.

3. CX-9

On the driver’s side, locate the vehicle’s taillight wiring

harness

-1

. Separate these connectors, being

careful not to break the locking tabs. Check to see that

the mating surfaces of the vehicle harness connectors

match the T-Connector ends. All connector surfaces

should be clean and free of dirt.

MAZDA-2

On the driver’s side, locate the vehicle’s taillight wiring

harness

-2

. Separate these connectors, being

careful not to break the locking tabs. Check to see that

the mating surfaces of the vehicle harness connectors

match the T-Connector ends. All connector surfaces

should be clean and free of dirt.

MAZDA-5

On the driver’s side, locate the vehicle’s taillight wiring

harness

-3

. Separate these connectors, being

careful not to break the locking tabs. Check to see that

the mating surfaces of the vehicle harness connectors

match the T-Connector ends. All connector surfaces

should be clean and free of dirt.

4. On the driver’s side, attach the end of the T-Connector

containing the yellow and the brown wires. Ensure

that the connectors are fully inserted with locking

tabs in place.

5. Route the T-Connector containing the green wire

below the threshold cover to the passenger’s side

taillight housing. Repeat step 4 using the T-Connector

ends containing the green wire.

NOTE

Route the 4-Flat through the driver’s side trim panel

into storage compartment on the threshold and store

there when not in use. When in use pull 4-Flat through

the door

6. On driver’s side, locate a ﬂat surface in a out of

the way place and mount the T-Connector’s black

convertor box with the double sided tape.

7. Locate a suitable grounding point near the connector

such as the vehicle’s frame or cross member.

(Do not drill into vehicle ﬂoor or bed.) Clean dirt and

rustprooﬁng from area. Drill a 3/32” hole and secure

white wire using eyelet and screw provided.

CAUTION

Verify what is behind any surface prior to drilling to

avoid damage to the vehicle and/ or personal injury.

Do not drill into any exposed surfaces.

WARNING

Be careful not to pinch harness in door latch.

8. On the driver’s side, locate the red 12 ga. Power wire

from the T-Connector box. Attach the black 12 ga.

wire provided.

9. Either route the black wire thru a grommet and along

the exterior frame or follow the existing wiring along

the thresholds into the engine compartment up to the

battery avoiding areas that may pinch or break the

wire

WARNING

If routing the wire thru a grommet and along the

exterior of the vehicle, be careful to avoid any hot

pipes, heat shields, the fuel tank or any other points

that may pinch or break the wire.

10. Disconnect the vehicle’s Negative (-) battery cable. If

not removed, remove the fuse from the yellow fuse

holder (provided). After cutting the fuse holder wire

, attach the ring terminal and secure to the vehicle’s

Positive (+) battery cable

. Connect the other end

of the fuse holder to the black 12 ga. wire, using the

yellow butt connector (provided)

WARNING

Read and follow all warnings and cautions printed

on the tow vehicle’s battery.

11. Reconnect the vehicle’s Negative (-) battery cable

and install the 10 amp fuse into the fuse holder

from Step 10.

WARNING

All connections must be complete for the T-Connector

to function properly. Test and verify installation with a

test light or trailer once installed. For initial test, reset

vehicle electrical system by temporarily removing the

key from the ignition.

12. Secure the remainder of the T-Connector harness with

the cable ties provided, to prevent damage or rattling

and being careful to avoid any areas that would pinch,

cut or melt the wire.

13. Reinstall the plastic trim panels, threshold, storage

covers, ﬂoor covering and other items removed during

installation, being careful not to pinch or cut the wires.

WARNING

Overloading circuit can cause ﬁres. DO NOT exceed

lower of towing manufacturer rating or:

• Max. stop/turn light: 1 per side (2.1 amps)

• Max. tail lights: (5.6 amps)

Read vehicle’s owners manual & instruction sheet

for additional information.

Mazda CX-9 Mazda M5 Mazda M2

h h

-2

-1

-3

1 2

FraNçaIS 2

Summary of Contents

Page 1

READ THIS FIRST:Read and follow all vehicle warnings and installation instructions before beginning installation. Wear safety glasses and use all saf

Page 2 - FraNçaIS

thermiques, le réservoir de carburant ou tout autre endroit susceptible de coincer ou endommager le ﬁl.10. Débrancher le câble de la borne négative (

Comments to this Manuals

No comments

Draw-tite 118520 T-ONE CONNECTOR User Manual

Browse online or download User Manual for For the car Draw-tite 118520 T-ONE CONNECTOR. Draw-Tite 118520 T-ONE CONNECTOR User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Draw-tite 118520 T-ONE CONNECTOR